Step 3:
Fit Kits for motors LARGER than 30HP.
Note: These fit kits CONTAIN Neutral Safety Interface to protect motor's gear box.

These Fit Kits contain one WATERPROOF servo motor, bracket, linkage and Neutral Safety Interface to allow it to operate motor's throttle.

Please use APPLICATION GUIDE to verify fit kit BEFORE ordering.

Mercury 40 / 50 / 60 HP
Remote control "T" Handle & Big Tiller Models ONLY
Serial # 1C050252 and Up

M456.WP Fit Kit   Qty: @ $202.00 Each


Mercury 75 / 90 / 115 HP
Remote control "T" Handle Models ONLY
Serial # 2B095049 and Up

M7.9.11.WP Fit Kit   Qty: @191.00 Each

Step 4 - Purchase OPTIONAL Accessory:
Remote Idle Run Switch

Weather proof touch pads that allow you to "Clone" the Idle / Run button on iTroll's control head so you can place them anywhere in your boat. Only compatible with iTroll G2 and G3 electronics.

You can install multiple switches. It is quite common to have a switch in each rear corner of a boat for maximum convenience!

Part# IT.Remote.Switch
Qty: @ $30.00 Each

Step 5 - Purchase OPTIONAL Accessory:
Polymer Custom Mount

Made of black Marine Grade Polymer. Allows perfect integration with one inch ball RAM mounts.

Note:
If you purchase this item with an iTroll electronics package (Step 1, above), the Polymer mount is factory installed on the iTroll control head.

A stand alone purchase of this item is for field installation on a iTroll that is already in service (minor disassembly of the iTroll control head is required).

Part# IT.P.Mount
Qty: @ $70.00 Each

Step 6 - Purchase OPTIONAL Accessory:
Billet Custom Mount

Made of Anodized Aluminum. Allows perfect integration with one inch ball RAM mounts. This mount is visually striking and adds incredible "Bling" to your dashboard!

Note:
If you purchase this item with an iTroll electronics package (Step 1, above), the Billet mount is factory installed on the iTroll control head.

A stand alone purchase of this item is for field installation on a iTroll that is already in service (minor disassembly of the iTroll control head is required).

Part# IT.B.Mount
Qty: @ $105.00 Each

Step 7 - Purchase OPTIONAL Accessory:
RAM Mount 1 Inch Ball Diamond Base

Base plate footprint = 2.43 x 1.31 inches
Hole size (diameter) = 0.22 inches
Spacing between holes (center to center) = 1.912 inches

Note: Our custom mounts have a one inch ball that sticks out of the back of the iTroll control head. A RAM base and arm completes your custom installation!

Part# RAM.Diamond
Qty: @ 9.50 Each

Step 8 - Purchase OPTIONAL Accessory:
RAM Mount 1 Inch Ball Round Base

Base diameter = 2.5 inches

Note: Our custom mounts have a one inch ball that sticks out of the back of the iTroll control head. A RAM base and arm completes your custom installation!

Part# RAM.Round
Qty: @ $10.50 Each

Step 9 - Purchase OPTIONAL Accessory:
RAM Mount Short Arm for 1 Inch Balls

Overall length = 2.42 inches
Spacing between balls (center to center) = 1.75 inches

Note: Our custom mounts have a one inch ball that sticks out of the back of the iTroll control head. A RAM base and arm completes your custom installation!

Part# RAM.Short
Qty: @ $10.50 Each

Step 10 - Purchase OPTIONAL Accessory:
RAM Mount Medium Arm for 1 Inch Balls

Overall length = 3.73 inches
Spacing between balls (center to center) = 3.0 inches

Note: Our custom mounts have a one inch ball that sticks out of the back of the iTroll control head. A RAM base and arm completes your custom installation!


Part# RAM.Medium
Qty: @ $12.50 Each

Step 11 - Purchase OPTIONAL Accessory:
Cisco Plate to mount RAM Diamond Ball under Cisco electronics mount. Constructed from stainless steel.

Note: This is only the plate, Cisco mount and RAM Diamond ball NOT included.



Part# IT.Cisco
Qty: @ $12.00 Each

Step 12 - Purchase OPTIONAL Accessory:
Neutral Safety Interface

For remote shift & throttle motors ONLY! This interface allows iTroll to read the position of the shifter so it can automatically idle the motor when the shifter is placed in neutral.

Note: If you are purchasing any of the fit kits in Step 3, they include one of these interfaces. DO NOT buy an interface in this step.

Part# IT.NSI
Qty: @ $30.00 Each

Step 13 - Purchase OPTIONAL Accessory:
Spare / Replacement WATERPROOF Servo Motor

We offer these in case you want to keep a spare in your truck or boat.

Note: All iTroll OEM servo motors are manufactured by HiTec and are of top quality. Historically, these have proven to be ultra dependable and we DO NOT have chronic servo failures like the competition. However, many anglers that fish tournaments or take remote trips like to have a spare servo on hand.

Part# IT.WP.Servo
Qty: @ $77.50 Each

Shipping Rates for iTroll complete systems:
"Complete system" = One Electronics Package + One Fit Kit

USA orders: FREE
Canada Orders: $30.00

NOTICE: At the present time, iTroll products can only be ordered online if shipped to USA or Canada.

Please email for international ordering information.

Step 14 - Purchase your iTroll: